Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.

Want to see how the EGG is made? Click to Watch

OT - "Instant Pot" Brisket

HeavyG
HeavyG Posts: 10,380
in Off Topic
Howsabout a pressure cooker smoker to have your brisket ready in just 3 hours.


“Reality is that which, when you stop believing in it, doesn't go away.” ― Philip K. Diçk




· Share on FacebookShare on Twitter

Comments

  • thetrim
    thetrim Posts: 11,375
    Heresy
    =======================================
    XL 6/06, Mini 6/12, L 10/12, Mini #2 12/14 MiniMax 3/16 Large #2 11/20 Legacy from my FIL - RIP
    Tampa Bay, FL
    EIB 6 Oct 95
    · Share on FacebookShare on Twitter
  • jeffwit
    jeffwit Posts: 1,348
    Turbo Travis. 
    Jefferson, GA
    XL BGE, MM, Things to flip meat over and stuff
    Wife, 3 kids, 5 dogs, 4 cats, 12 chickens, 2 goats, 2 pigs. 
    “Honey, we bought a farm.”
    · Share on FacebookShare on Twitter
  • milesvdustin
    milesvdustin Posts: 2,882
    Faster bbq means less beer drinking time. Waste of money

    2 LBGE, Blackstone 36, Jumbo Joe

    Egging in Southern Illinois (Marion)

    · Share on FacebookShare on Twitter
  • YukonRon
    YukonRon Posts: 17,075
    Brisket looks really bad, but it does have a Honda power plant. Cook brisket and generate electricity? The future is here!!!!
    "Knowledge is Good" - Emil Faber

    XL and MM
    Louisville, Kentucky
    · Share on FacebookShare on Twitter
  • GregW
    GregW Posts: 2,678
    I think I've seen just about everything now.
    · Share on FacebookShare on Twitter
  • Photo Egg
    Photo Egg Posts: 12,132
    The Cajun Fryer Company designed theirs years ago. They have showed them at a few Eggfests in Texas. Pretty good food and much faster. Just lacks the good crust. Similar to those who foil at the end.
    https://cajunfryer.com/product-category/cajun-express-smoker/
    Thank you,
    Darian

    Galveston Texas
    · Share on FacebookShare on Twitter
  • Dobie
    Dobie Posts: 3,448
    I thought you were posting a cook, what was I thinking?   :|
    Jacksonville FL
    · Share on FacebookShare on Twitter
  • lkapigian
    lkapigian Posts: 11,119
    like to see the ASME plate for that 
    Visalia, Ca @lkapigian
    · Share on FacebookShare on Twitter
  • HendersonTRKing
    HendersonTRKing Posts: 1,803
    Only 45 minutes to cook a whole chicken!!

    https://forum.k-rigg.com/post/5-lb-whole-chicken-9813702
    It's a 302 thing . . .
    · Share on FacebookShare on Twitter
  • Legume
    Legume Posts: 15,173
    Their forum sucks.
    Love you bro!
    · Share on FacebookShare on Twitter
  • SGH
    SGH Posts: 28,877
    edited August 2018
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. At 15.1 psi, ASME Section VIII code becomes applicable. 

    Location- Just "this side" of Biloxi, Ms.

    Status- Standing by.

    The greatest barrier against all wisdom, the stronghold against knowledge itself, is the single thought, in ones mind, that they already have it all figured out. 

    · Share on FacebookShare on Twitter
  • nolaegghead
    nolaegghead Posts: 42,109
    SGH said:
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. 
    what do all those words mean?!
    ______________________________________________
    I love lamp..
    · Share on FacebookShare on Twitter
  • SGH
    SGH Posts: 28,877
    nolaegghead said:
    SGH said:
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. 
    what do all those words mean?!
    In short, buy a Muhle R41 =)

    Location- Just "this side" of Biloxi, Ms.

    Status- Standing by.

    The greatest barrier against all wisdom, the stronghold against knowledge itself, is the single thought, in ones mind, that they already have it all figured out. 

    · Share on FacebookShare on Twitter

Categories