Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.

Want to see how the EGG is made? Click to Watch

OT - "Instant Pot" Brisket

HeavyG
HeavyG Posts: 10,323
Howsabout a pressure cooker smoker to have your brisket ready in just 3 hours.


“Reality is that which, when you stop believing in it, doesn't go away.” ― Philip K. Diçk




Comments

  • thetrim
    thetrim Posts: 11,352
    Heresy
    =======================================
    XL 6/06, Mini 6/12, L 10/12, Mini #2 12/14 MiniMax 3/16 Large #2 11/20 Legacy from my FIL - RIP
    Tampa Bay, FL
    EIB 6 Oct 95
  • jeffwit
    jeffwit Posts: 1,348
    Turbo Travis. 
    Jefferson, GA
    XL BGE, MM, Things to flip meat over and stuff
    Wife, 3 kids, 5 dogs, 4 cats, 12 chickens, 2 goats, 2 pigs. 
    “Honey, we bought a farm.”
  • milesvdustin
    milesvdustin Posts: 2,882
    Faster bbq means less beer drinking time. Waste of money

    2 LBGE, Blackstone 36, Jumbo Joe

    Egging in Southern Illinois (Marion)

  • YukonRon
    YukonRon Posts: 16,984
    Brisket looks really bad, but it does have a Honda power plant. Cook brisket and generate electricity? The future is here!!!!
    "Knowledge is Good" - Emil Faber

    XL and MM
    Louisville, Kentucky
  • GregW
    GregW Posts: 2,676
    I think I've seen just about everything now.
  • Photo Egg
    Photo Egg Posts: 12,110
    The Cajun Fryer Company designed theirs years ago. They have showed them at a few Eggfests in Texas. Pretty good food and much faster. Just lacks the good crust. Similar to those who foil at the end.
    https://cajunfryer.com/product-category/cajun-express-smoker/
    Thank you,
    Darian

    Galveston Texas
  • Dobie
    Dobie Posts: 3,354
    I thought you were posting a cook, what was I thinking?   :|
    Jacksonville FL
  • lkapigian
    lkapigian Posts: 10,708
    like to see the ASME plate for that 
    Visalia, Ca @lkapigian
  • Only 45 minutes to cook a whole chicken!!

    https://forum.k-rigg.com/post/5-lb-whole-chicken-9813702
    It's a 302 thing . . .
  • Legume
    Legume Posts: 14,602
    Their forum sucks.
  • SGH
    SGH Posts: 28,791
    edited August 2018
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. At 15.1 psi, ASME Section VIII code becomes applicable. 

    Location- Just "this side" of Biloxi, Ms.

    Status- Standing by.

    The greatest barrier against all wisdom, the stronghold against knowledge itself, is the single thought, in ones mind, that they already have it all figured out. 

  • nolaegghead
    nolaegghead Posts: 42,102
    SGH said:
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. 
    what do all those words mean?!
    ______________________________________________
    I love lamp..
  • SGH
    SGH Posts: 28,791
    SGH said:
    lkapigian said:
    like to see the ASME plate for that 
    One is not required. It operates at less than 15 psi. ASME Section VIII Division 1 requirements starts at pressures above 15 psi up to 3000 psi. Division 2 covers 3000 psi up to 10,000 psi. Division 3 covers above 10,000 psi. Anything 15 psi and below are excluded from code stamping. 
    With that said, a manufacturer can build any piece of equipment using Section VIII rules of construction if so desired. This is actually a very common practice that is used just for the built in safety factor of the code. However, even if Section VIII code is used for construction, no stamping is required if the vessel or equipment operates at 15 psi or below. 
    what do all those words mean?!
    In short, buy a Muhle R41 =)

    Location- Just "this side" of Biloxi, Ms.

    Status- Standing by.

    The greatest barrier against all wisdom, the stronghold against knowledge itself, is the single thought, in ones mind, that they already have it all figured out.