BGE Cabinet Completed & Checked Out

EagleIII

BTW, if you ever quit your day job, you'd have a career building tables for the rest of us Eggers!

A31unit

Simply Amazing!

Thatgrimguy

That AWESOME!! Love it!

EggHeadDad

Toxarch said:

Where's the dimmer controls located?

I have an RF dimmer controller located under the top above the top drawer.  You can see a picture in my Flickr album at:  https://flic.kr/s/aHskdd8Ebd

EggHeadDad

chadgremillion said:

About how much did it run to construct?

I haven't tallied the full cost but I estimate $1,200 in materials and 80 hours in my labor.  The main cost driver was the Sapele wood (100 bf at $8.00/bf milled).

EggHeadDad

EagleIII said:

BTW, if you ever quit your day job, you'd have a career building tables for the rest of us Eggers!

I need to get my girls out of college and a space to build that isn't my wife's parking place in the garage. 

EggHeadDad

shadowrider said:

 I need to buy a bunch more clamps. 

Yeah, you can never have too many clamps on a large glue-up. 

bluebird66

Awesome build!

pswarren

WOW! Gorgeous table! That is quite the Festool collection as well.

EggHeadDad

pswarren said:

WOW! Gorgeous table! That is quite the Festool collection as well.

Thanks.  I love my Festool collection.  Everytime I get them out I remember just how great they are to work with.

Cookbook_Chip

Beautiful work. Love the LEDs!

blasting

Very impressive table.  But that write up was incredible.   Thanks for documenting so carefully.  

If you don't mind me asking, I'm curious what you have in it for materials?  My guess would be about $1300 - close?

Enjoy your beautiful new set up.

Edit. Didnt see second page when I posted. Saw you answered already about $.

DoubleEgger

LOVE IT. The attention to detail is amazing. Thank you for sharing and inspiring. True craftsmanship is becoming a lost art. 

Thecoiman

That is truly a beautiful table and functional. I am envious of your wood working skills.

PorkU

@browntw79 I have a very special table coming that should be finished tomorrow or Friday of this week and I can only hope its half as nice as what you have built!!  What an unbelievable looking table...Clean and modern.  Awesome set up my man!!

Sonny3

World Class for sure.  Makes my little table build look pale in comparison.  You obviously are one very talented dude.  Nice job sir.

EggHeadDad

PorkU said:

@browntw79 I have a very special table coming that should be finished tomorrow or Friday of this week

Thanks @PorkU.  Post pics of your table once you're up and running.

EggHeadDad

Thanks @Sonny3. Keep choking the life out of every day!

EggHeadDad

I finally got my backordered handles delivered this week.  This was the original vision I had in May.  Cheers!




More pictures posted on Flickr at https://flic.kr/s/aHskdd8Ebd

PMG

@EggHeadDad - MAN U Did it!  Very Nicely done!  I like your choice of wood and the whole color scheme!!!  LED's are a nice touch!  Remember mine>!

PMG

@EggHeadDad - I saw your Flickr pic page!  Man nice setup and great use of your skillz!  For the heat situation inside the cabinet...I purchased some 1/2" Aluminum plates from a local vendor and seems to be working well!  Keeps heat transfer to a minimum!  I had it powder coated matte black!  As far as "Kiln Fabric" or heat fabric I used some from a company call Gladiator Glove works!  Google them!  Their rated up to 1,500 deg F!?

PMG

Another Pic of my application of the tape fabric!  Man that High Grade Cedar talbe top is dry and I feel it may go up in flames SO I didn't want to take any chances!  Too much TIME and MONEY invested!

rmercier

Amazing! Kudos and thanks for the great details

EggHeadDad

@PMG - Thanks for the additional information.  I am watching my box temps but have not really had any concerns to date.  I do like the metal plate idea used as a heat sink.  Thanks.

EggHeadDad

PMG said:

@EggHeadDad - MAN U Did it!  Very Nicely done!  I like your choice of wood and the whole color scheme!!!  LED's are a nice touch!  Remember mine>!

You were part of my inspiration!  Thanks again for all you build photos.

robnybbq

Very Very nice

jollygreenegg

Awesome table!  

Ross in Ventura

browntw79 said:

As promised, I wanted to share my design thoughts and lessons learned from my table build.  As noted in an earlier post (posted under browntw79), I was inspired to go crazy after seeing the tables of @cazzy and @PMG. I was especially impressed with @PMG’s build pictures. When I decided that I needed to replace my existing table I also decided to document the build for future wood working enthusiast that might be looking to build a BGE table.  Besides a few pages of rough sketches and dimension calculations I had no real plans other than some ideas.  I started with some simple specifications for this project to include:

• Can bear the weight of the concrete pad and the BGE
• Table height of about 36” (personal preference)
• Fits under a custom cover I had made for original stand
• Fits within the deck bump out space (76” wide)
• Is mobile enough to move around the deck
• Has 3 to 4 drawers
• Has an area that could take hot items without damaging the wood

The Frame (aka the Skeleton): I used stock pressure treated 2x4 lumber that I selected for straightness.  The PT lumber was extremely wet when I started with some of the 8 footers weighing close to 20 pounds.  I calculated the height of the BGE shelf with the plan of using a 16x16 inch concrete paver block.  My first revelation was this was quickly getting to be extremely heavy.  I used my Festool Domino 500Q jointer for all the frame joints with 10 x 50mm exterior grade Dominos.  All the joints were glued using Titebond III wood glue.  Even with the wet wood the glue appeared to create a solid bond.  Most of the joints include a long decking screw as well to hold them tight as the glue dried.

Redesign Note:  The largest weight bearing section of the table is the “cube” under the Egg.  If I were to do the design over I would use PT 1x4 for all the framing and only use 2x4 for the BGE shelf cube.

Exterior Wood:  After consulting with my local hardwood supplier (Colonial Hardwood in Springfield, VA) I selected to go with African Sapele that is a member of the mahogany family.  It is very dense weighing about 3.4 pounds per board foot (similar to red oak).  As you can see the featuring in the wood is stunning.  I had the mill shop plane and sand the boards I selected.  Started with a purchase of 100 bf based on some of those scribbled calculations.  I actually was pretty close to being correct.  All the boards were milled down to ¾” thickness.  I did end up going back to Colonial for a couple more pieces for the top and had them milled to 7/8” (which created another problem down stream).

For the Exterior Walls I decided to make 3 1/4” wide wanes coat slats with a V-notched tongue and groove that interlock on the sides and are tacked at the top and bottom with galvanized staples.  The effect of the wanes coating turned out very nice with the v-notch breaking up the visual difference between boards.

The Face Frame was fairly straightforward to assemble after I decided on the dimensions of the pieces.  Because I was covering “the Skeleton” I had to make some of the pieces wider than I would prefer.  I literally sat in front table one night for hours clamping on various sizes of boards to see what worked best.  I decided on making the two outside vertical pieces the same width for symmetry and I eliminated the cross member on “the skeleton’s” right side. 

Note:  I stained the concrete block with some walnut stain to allow it to blend into the cabinet better.

The Drawers:  Once the face frame was completed I knew the opening dimensions so I could work the drawers.  Last December I rebuilt all my drawers in our kitchen using half blind dovetails for the 5/8” maple boxes with a birch bottom.  I repeated this design for this table and used the Blum Tandem concealed full extension sliders with Blumotion (soft close) feature for all the drawers.  The slides are spec’d for up to 100 lbs so holding Eggcessories is no problem.  For the fronts, I had set aside some select pieces for appearance.  The fronts are simply rounded over with a 3/8” round-over bit and drilled for the stainless steel (288mm center-to-center) handles.  I have lined three of the drawer bottoms with a cork sheeting and the fourth with a non-slip kitchen drawer liner.  I will watch the drawers over time for any evidence of water damage.  I’m hoping to keep most water out of the drawer using three methods . . . .

1. Keep it covered with my Sunbrella custom cover (unfortunately my supplier is out of business)
2. Wide lip on the top (2 ½ inches at the front)
3. Metal flashing over the left drawer (below the concrete block)

For the Top I wanted two layers to form a 1 ½” top more for visual effects than strength.  At $8.00 bf (milled) I didn’t want to waste Sapele wood on the bottom layer.  I decided to build a frame for the bottom and then fill it in with cheaper poplar.  But I knew I wanted it to appear like two layers of Sapele at the opening for the Egg as well.  This ended up proving to be time consuming and tricky.  In the end wasting $8.00 bf for the center “core” might have been more economical.  On the top layer I needed only to factor in the framed area for the four granite tiles.  Once completed, I cut the circle for the Egg opening (based on calculations).  Next was time for finishing. 

Finish:  I started with sanding everything with 220 grit paper.  Then I applied two coats of Watco Teak Oil finish followed by two coats of marine grade spar vanish.  For the top I applied three coats but was not satisfied with the sheen.  I ended up lightly sanding it with 220 grit sandpaper and then spraying on two additional thin layers of spray vanish.  I am very please with the results.

LED Lighting:  I noticed several members had included various forms of lighting on their Egg.  I selected an outdoor 3528 daylight white LED tape.  I routed in a channel following the contour of the front edge and inserted bright white LED lights tied into a dimmer remote.  This provides great lighting at night to see in the drawers as well as an impressive visual effect at night.

Post Fit Check Modifications:  I dropped my large BGE in on Friday evening and opened it for the first time.  Ouch!  I had interference under the hinge marring that fine finish.  Crap!  Remember when I changed the thickness of the top’s upper layer?  Clearly I didn’t.  I ended up removing the concrete block and shimming it up and reinstalling the entire Egg.  I also was uncomfortable with the Egg opening and decide to cut out an additional ½” of radius.  At 21 ¾” diameter it provides me with ¾” to 1” of an air gap around the Egg.  I have also noticed the casters are hard to get rolling.  I might be switching them out for a set of 2” solid steel casters.

Water Test:  On the 4th of July, during my first smoke, the heavens above my house opened up and poured on my new creation during the smoke.  Surprisingly, there was only minimal water in the left drawer (my son claimed it was because I peaked three times) and none in the right drawers.  Design success?!?!  We will see.

Final Specifications:

Length:  71 ½”

Depth:  33”

Height:  37” 

Weight:  Very Heavy (estimate 400 to 500 lbs)

Power:  

• 120V outlet located inside near top drawer
• 12V for LED Lighting
• 5V for Stoker controller

Supplies List (Suppliers):

• 10 – 2” x 4” pressure treated pine (Home Depot)
• 120 board feet – African Sapele (Colonial Hardwood)
• 8 board feet – Poplar (Home Depot)
• 20 board feet – Maple (Home Depot)
• 4 – 12” x 12” Granite tiles, Ubatuba (Floors & Decors)
• ¼” Backerboard (Home Depot)
• Black silicone caulk (Floors & Decors)
• 12V Flexible LED Strip Lights with power supply & RF dimmer (Amazon)
• Big Green Egg large table nest
• Custom Walnut Handle (AMLWoodart.com)
• Tongue and Groove V-Notch Router Bit set (Amazon)
• Festool Domino tenons, Sipo Mahogany (Local Woodcraft Store)
• Polished Stainless Steel Starr “X” bottle opener (Amazon)
• 6 – 3 inch 150-pound swivel polyurethane plate casters (Amazon)
• 4 pairs of 21” Blum Tandem with Blumotion 563H sliders (Amazon)
• 6 - Stainless Steel hooks (GreenBoatStuff.com)
• 4 - Stainless Steel handles, 288mm center-to-center (CabinetParts.com)
• 1 quart of Watco Teak Oil Finish (Home Depot)
• 1 quart of System Three Marine Spar Varnish, Satin (Local Woodcraft Store)

Please check out the photos of all stages of the build on my Flickr page. 

Enjoy and good luck with any new builds this inspires!  Feel free to post questions or PM me.

Cheers!

Tom

P.S.  I managed to post this under my @browntw79 persona by accident; I meant to post it using my @EggHeadDad account.  Oops!  Too much beer last night perhaps?  

 

Great looking Table Tom

Ross

EggHeadDad

Ross in Ventura said:

Great looking Table Tom

Thanks man!

CDPlaya

Awesome. , you need to mass product these, you will get rich quick!