Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Want to see how the EGG is made? Click to Watch
Facebook | Twitter | Instagram | Pinterest | Youtube | Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Want to see how the EGG is made? Click to Watch
Trouble keeping temp down. DigIQ
Options
Hibby
Posts: 606
First low and slow.
Filled charcoal ring to line with lump.
Started with small wax/sawdust starter in the center. Waited about fifteen minutes before turning DigIQ on (first use). Daisy wheel with less than half an ellipse open. Pit viper fully open. Set pit temp to 200 but the pit keeps fluctuating between 213 and 225. I'm not horribly concerned but just wish it would sit still at 200. Any ideas?
I cook. I eat. I repeat. Thornville, Ohio
Comments
-
Close the damper on the pit viper to half open. It will move less air but still move enough to keep the pit at your desired temp. On my large I usually set it at a half to a quarter open.XLBGE & LBGENorth Richland Hills, TX
-
You have to pretty much close the top vents completely. I leave the little holes just barely cracked on mine and that's when I am going for 250.
-
Just purchased the CyberQ Wifi! Can't wait to use it this weekend!
________________________________________________________________________
XLg BGE - JANUARY 2013
Spare rib anyone? – Adam
-
Any cooker needs a healthy amount of air moving thru it for it not to go out. I find that 225 is about as low as I trust for a long cook on the BGE. The ceramics hold 200 degrees in the thermal mass it has, so once you see a dip in the dome temps the fire could have been out for an hour or so before you realize there is a problem. The key to cooking is knowing when to stop, cook hotter and pull when ready.
Hope that helps.
-SMITTY
from SANTA CLARA, CA
-
Why do you want the temp on 200 @ grid? Anywhere below 250 is plenty low and slow. As someone stated above with your bottom damper wide open it would be almost impossible to keep the temp at 200 and maintain airflow.I'm a DigiQ owner and if you will set it for 225-230 and half open at the bottom and about half an eyelet open at the top it will perform great.
-
normally when i use my DigiQ i set it at 265 damper on the fan at half. light my coals allowing the unit to bring the grill up to temp daisy wheel petals open till about 255 then i close them . the fan supplies more than enough air to power through the coal and maintain temp .never had a issue holding it and i use it primarily on my large which has no gasket.Large Big Green Egg , XL Big Green Egg . BBQ Guru, Weber Kettle, Weber Q grill for road trips.
-
If it's the 10 cfm blower make a quarter moon shape out of it.
Steve
Caledon, ON
-
Well, I've got mixed emotions about my cook last night. I definitely need to learn more. I was able to get the temp to stabilize at 250 but unsuccessful any lower than that. I only ever closed pit viper damper to 1/2 and as some recommended, even more closed might have gotten me where I wanted. I also made the mistake of putting the meat probe in not the right place. Alarm going off that meat was done and I was suspicious that it was too soon. I pulled the proven and placed it elsewhere and the temp dropped to 170 so I definitely need to figure out the best penetration point (☺). Overall time wasn't nearly long enough IMHO (7.5 hours) so I'm confused about that as well. As for the meat, great taste and nice ring. A few spots tasted over-smoked (meat was placed in egg within 30 minutes of ignition). Certain parts of the meat seem over-cooked and mushy. But also spots with copious amounts of un-rendered fat. All meat seemed completely done. As for how I set it up, I was going off a recommendation from someone with an egg. Plate setter legs down. Pit probe laying directly on surface of plate setter. Shoulder directly on plate setter. No foil (what a mess afterwards). Much to learn but thanks for earlier help and for any advice you can offer.I cook. I eat. I repeat. Thornville, Ohio
-
Think about it this way. The fan can only make the temp go up. The more opening you have in the barrel the more draught you will have. To maintain low temps takes very little air. The fan can overcome the small aperture and supply enough air as long as the damper is not completely closed. 1/4 moon shape or less on a 10 cfm fan is more than enough.
Steve
Caledon, ON
-
"Plate setter legs down. Pit probe laying directly on surface of plate setter. Shoulder directly on plate setter."I haven't done one yet, but this doesn't sound right. I've always heard PS legs up, then grate, then shoulder. Probe should go in thickest part of the meat, but not next to a bone.------------------------------------------------------------------------LBGE 2013 - MiniMax 2015 - Seemingly every accessory the fine folks at CGS sell - Fightin' Texas Aggie till I die - Gig 'Em - Located in the bright lights of Dallas
-
Hibby said:Well, I've got mixed emotions about my cook last night. I definitely need to learn more. I was able to get the temp to stabilize at 250 but unsuccessful any lower than that. I only ever closed pit viper damper to 1/2 and as some recommended, even more closed might have gotten me where I wanted. I also made the mistake of putting the meat probe in not the right place. Alarm going off that meat was done and I was suspicious that it was too soon. I pulled the proven and placed it elsewhere and the temp dropped to 170 so I definitely need to figure out the best penetration point (☺). Overall time wasn't nearly long enough IMHO (7.5 hours) so I'm confused about that as well. As for the meat, great taste and nice ring. A few spots tasted over-smoked (meat was placed in egg within 30 minutes of ignition). Certain parts of the meat seem over-cooked and mushy. But also spots with copious amounts of un-rendered fat. All meat seemed completely done. As for how I set it up, I was going off a recommendation from someone with an egg. Plate setter legs down. Pit probe laying directly on surface of plate setter. Shoulder directly on plate setter. No foil (what a mess afterwards). Much to learn but thanks for earlier help and for any advice you can offer.
-
Huh. Not sure what you are trying to cook. When I use my digi2 at 250 I have the daisy wheel holes closed all the way. And the ellipse open 1/8th of an inch. Maybe. And the fan open only 1/4 of the way. The temps you are looking for I would have closed both a touch more.-------------------------------------------------------------------------------Strongsville, OhioYes. I own a blue egg! Call Atlanta if you don't believe me![I put this here so everyone knows when I put pictures up with a blue egg in it]
-
One more thing. Only reason I can think of to cook at those temps is cold smoked cheese, cold smoked salmon, or maybe even beef jerky. Am I close?-------------------------------------------------------------------------------Strongsville, OhioYes. I own a blue egg! Call Atlanta if you don't believe me![I put this here so everyone knows when I put pictures up with a blue egg in it]
-
I was cooking a pork shoulderI cook. I eat. I repeat. Thornville, Ohio
-
@Hibby - you have received good advice in this thread. I have used my Guru's and had rock solid results everytime. The dynamics of the fire you start with before starting up the guru can play into temp swings. I have had a couple cooks where the temps would vary a bit from the set point, but nothing more than 15 - 20 degrees tops. For what its worth...I tried jerky on my large with my Cyber Q WiFi and it stabilized @ 160 degress with no problem and stayed that way for over 4 hours. Use some of the advice provided here and you'll be very happy next time. >-
-
@Hibby - got it! Next time try lighting the lump only at the top of the firebox in the center. No daisy holes. Just open the ellipse about 1/8th inch. And close the fan to 1/4 when you get to your desired temp. With shoulder I'd shoot somewhere between 225-250. Naked whiz has recipes on his site detailing how to maintain some really low temps if you are looking for that.-------------------------------------------------------------------------------Strongsville, OhioYes. I own a blue egg! Call Atlanta if you don't believe me![I put this here so everyone knows when I put pictures up with a blue egg in it]
Categories
- All Categories
- 182.7K EggHead Forum
- 15.7K Forum List
- 459 EGGtoberfest
- 1.9K Forum Feedback
- 10.3K Off Topic
- 2.2K EGG Table Forum
- 1 Rules & Disclaimer
- 9K Cookbook
- 12 Valentines Day
- 91 Holiday Recipes
- 223 Appetizers
- 516 Baking
- 2.4K Beef
- 88 Desserts
- 163 Lamb
- 2.4K Pork
- 1.5K Poultry
- 30 Salads and Dressings
- 320 Sauces, Rubs, Marinades
- 543 Seafood
- 175 Sides
- 121 Soups, Stews, Chilis
- 35 Vegetarian
- 100 Vegetables
- 313 Health
- 293 Weight Loss Forum