Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Want to see how the EGG is made? Click to Watch
Facebook | Twitter | Instagram | Pinterest | Youtube | Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Want to see how the EGG is made? Click to Watch
Dome Alignment and Dollar Bill Test
SmokeOnTheMountain
Posts: 51
Hello all. So I recently replaced my gasket and my band on my egg. I have been fiddling with them off and on over the past few days and taking breaks as my frustration builds. At this point I’m probably 5-6+ hours in of fiddling and so far I can either get proper dome alignment with no underbite/overbite along with a poor seal at a few different positions. Or I can get a great deal with about a 1/4” under/overbite. It’s an XL and I’m not sure if having a poor seal in those few spots is a deal breaker. I can’t see a visible gap but a dollar bill pulls fairly easily through those spots. Any advice appreciated!
Comments
-
I have a LBGE but independent of the size rig, I would default to the good seal. As you well know, the BGE runs on air flow and you think you control it thru the lower vent and whatever the former DFMT is called.With the gap(s) you can manage the system introduced air flow by reducing the vent settings but if the introduced air flow is high, then maintaining L&S cook temps could be a challenge.Shutdown could be a whole 'nother story. But just an opinion and we all know what those are worth...Louisville; Rolling smoke in the neighbourhood. # 38 for the win. Life is too short for light/lite beer! Seems I'm livin in a transitional period.
-
1/4”? No offense meant, but a BGE is not fine China! Your dome and base were not made as one piece and then cut apart! They were made in separate molds and often days apart! Please send me a PM on this forum unless you know my email address.
-
@RRP that’s what I was thinking. But after reading some posts of people who had perfect alignment and good deal I kept trying to figure out what I was doing wrong. I sent you an email.
@lousubcap thank you! I was on the same thought process but wanted to make sure before I went that route. -
As mentioned above, sweat about the seal if you must, but don't worry about 1/4" under/overbite. Your sanity is worth far more.#1 LBGE December 2012 • #2 SBGE February 2013 • #3 Mini May 2013A happy BGE family in Houston, TX.
-
SmokeOnTheMountain said:@RRP that’s what I was thinking. But after reading some posts of people who had perfect alignment and good deal I kept trying to figure out what I was doing wrong. I sent you an email.
@lousubcap thank you! I was on the same thought process but wanted to make sure before I went that route.
Paul - thanks for the pictures you sent me and I hope you understand my reply I sent you about my observations. After 21 years of providing this service I have some pretty good clues!
Categories
- All Categories
- 183.2K EggHead Forum
- 15.8K Forum List
- 460 EGGtoberfest
- 1.9K Forum Feedback
- 10.4K Off Topic
- 2.2K EGG Table Forum
- 1 Rules & Disclaimer
- 9K Cookbook
- 12 Valentines Day
- 91 Holiday Recipes
- 223 Appetizers
- 517 Baking
- 2.5K Beef
- 88 Desserts
- 167 Lamb
- 2.4K Pork
- 1.5K Poultry
- 32 Salads and Dressings
- 320 Sauces, Rubs, Marinades
- 544 Seafood
- 175 Sides
- 121 Soups, Stews, Chilis
- 38 Vegetarian
- 102 Vegetables
- 315 Health
- 293 Weight Loss Forum