Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.

Want to see how the EGG is made? Click to Watch

Advice Re Removing Gasket

Dondgc
Dondgc Posts: 709
in EggHead Forum
I have a new Rutland coming from @RRP that I would like to install before National Brisket Day. What tools/supplies would those who have removed an old gasket before recommend having on hand? I believe I need a brush but not a rotary brush - any particular type? A scraper - would this be a razor scraper or more like a paint removal scraper? Acetone? Or is it needed once I’m down to nothing but old adhesive? Anything else?

thanks in advance. 
New Orleans LA
· Share on FacebookShare on Twitter

Comments

  • jdMyers
    jdMyers Posts: 1,339
    edited May 2020
    Piece of cake...   harbor freight.  Use plastic to remove bulk peel etc.  Use sand disk and acetone to remove gasget seal glue residue.  Dont worry about minor stuff.  Dont sig down into the ceramic.  Rub down with alcohol and stick on new.


    Columbus, Ohio
    · Share on FacebookShare on Twitter
  • Carolina Q
    Carolina Q Posts: 14,831
    Ron's "kit" will include those directions. Personally, I didn't much bother. I scraped the old off as best I could, didn't go out and and buy any new tools, applied the Permatex then the gasket. That was 10 years ago. Been fine ever since.

    I hate it when I go to the kitchen for food and all I find are ingredients!                                                                                                                                                                                                                           

    Michael 
    Central Connecticut 

    · Share on FacebookShare on Twitter
  • buzd504
    buzd504 Posts: 3,878
    edited May 2020
    I used a pumice stone.  Worked great.

    (Note - my gasket was mostly gone already).
    NOLA
    · Share on FacebookShare on Twitter
  • RRP
    RRP Posts: 26,465
    edited May 2020
    Dondgc said:
    I have a new Rutland coming from @RRP that I would like to install before National Brisket Day. What tools/supplies would those who have removed an old gasket before recommend having on hand? I believe I need a brush but not a rotary brush - any particular type? A scraper - would this be a razor scraper or more like a paint removal scraper? Acetone? Or is it needed once I’m down to nothing but old adhesive? Anything else?

    thanks in advance. 
     I cover the tools and methods in those instructions coming with your gasket.
    Re-gasketing the USA one yard at a time 
    · Share on FacebookShare on Twitter
  • kl8ton
    kl8ton Posts: 6,434
    +1 on pumice stone
    cheap too

    $2.49 at Home Depot.  I think i used 2.5 of them. . . maybe 3.


    Large, Medium, MiniMax, 36" Blackstone
    Grand Rapids MI
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,762
    Scrape off what you can, torch the rest, scrape again, torch again, etc.  If the ceramic is already hot from a cook, that helps too.
    · Share on FacebookShare on Twitter
  • 1voyager
    1voyager Posts: 1,161
    I painted the gasket with acetone and let it sit for about an hour. Then I used a putty knife to scrape off gasket. It came off in one piece.

    The only downside is that acetone is nasty stuff.
    Large Egg, PGS A40 gasser.
    · Share on FacebookShare on Twitter

Categories