Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.

Want to see how the EGG is made? Click to Watch

Rutland Gasket Install Help!

CouplesCaddy
CouplesCaddy Posts: 9
in EggHead Forum
Hey guys, been egging for about 5 years now, and am FINALLY jumping into the idea of using a good gasket on my medium & large BGEs.  I just installed the gaskets and I can't get the hinge to close the lid on my medium, and during the install on my large i decided to update the hinge to the new one as my last one is F'd.  anybody have any advice to this issue?  is it entirely just a break in period to get the gasket to relax into place and flatten out?  the lid is literally about an inch above where it used to be.

Immediate help would be greatly appreciated as I'm doing a large cook tomorrow to take to my parents house in the 'rona quarantine here in CA.

thanks so much guys!
· Share on FacebookShare on Twitter

Comments

  • GregW
    GregW Posts: 2,678
    @CouplesCaddy- I sent you a PM
    · Share on FacebookShare on Twitter
  • JonWesson
    JonWesson Posts: 166
    what is this rutland gasket?
    large small and mini all in legal proceedings but i can use them for now no more, all gone                                                                                                                        usa somewhere on the road
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,758
    edited March 2020
    That makes no sense.  You took off a piece of gasket and replaced it with another.  The band can slide up and down vertically on the dome and base to adjust the alignment. a few millimeters.  There's no way it can be an inch off if properly assembled.

    Post some pics.  I'm leaning toward you have the hinges installed upside down or backwards.
    · Share on FacebookShare on Twitter
  • Legume
    Legume Posts: 15,936
    Did you put Rutland on both top and bottom?  Only needs to be on bottom
    THANK YOU FOR YOUR ATTENTION TO THIS MATTER
    · Share on FacebookShare on Twitter
  • bradleya123
    bradleya123 Posts: 485
    I just replaced my gasket with a Rutland, woozier what a difference!!  I've always had small leak somewhere on my Large but after installing (Easy Peasy) the Rutland, zero leaks!  Perfect!!  Only installed on the bottom.

    Retired Navy, LBGE
    Pinehurst, NC

    · Share on FacebookShare on Twitter
  • CouplesCaddy
    CouplesCaddy Posts: 9
    Hey guys, the new style hinge on my large seemed to adjust into a pretty good setting for the rutland. But after 15-20 mins of messing with my medium with old style hinge, this is where its chilling.
    · Share on FacebookShare on Twitter
  • CouplesCaddy
    CouplesCaddy Posts: 9
    Its totally binding up on the back gasket section, almost rolling it off the base
    · Share on FacebookShare on Twitter
  • Mattman3969
    Mattman3969 Posts: 10,458
    Is that a rope style gasket?

    -----------------------------------------

    analyze adapt overcome

    2008 -Large BGE. 2013- Small BGE and 2015 - Mini. Henderson, Ky.
    · Share on FacebookShare on Twitter
  • Legume
    Legume Posts: 15,936
    That gasket doesn’t look right.  Should be flat, that looks like thick rope.
    THANK YOU FOR YOUR ATTENTION TO THIS MATTER
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,758
    You need the flat gasket......you bought the rope gasket.
    · Share on FacebookShare on Twitter
  • alaskanassasin
    alaskanassasin Posts: 8,898
    Where the fahk is @rrp!?
    South of Columbus, Ohio.


    · Share on FacebookShare on Twitter
  • Canugghead
    Canugghead Posts: 13,654
    installed a rope type on XL few months ago, bottom only, no problem, dome weight flattens it.  a friend gave it to me years ago, I think it's cotronics but not 100% sure


    canuckland
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,758
    edited March 2020
    Canugghead said:
    installed a rope type on XL few months ago, bottom only, no problem, dome weight flattens it.  a friend gave it to me years ago, I think it's cotronics but not 100% sure


    The Cotronics woven ceramic gaskets are a lot less "fluffy" than the Rutlands though.  The 5/8" rutland stays pretty thick whereas the flat Cotronics one would pancake down to nothing.  
    · Share on FacebookShare on Twitter
  • GregW
    GregW Posts: 2,678
    alaskanassasin said:
    Where the fahk is @rrp!?
    I Private messaged @CouplesCaddy to contact RRP via PM. RRP can also be reached via the other forum.
    · Share on FacebookShare on Twitter
  • Canugghead
    Canugghead Posts: 13,654
    stlcharcoal said:
    Canugghead said:
    installed a rope type on XL few months ago, bottom only, no problem, dome weight flattens it.  a friend gave it to me years ago, I think it's cotronics but not 100% sure


    The Cotronics woven ceramic gaskets are a lot less "fluffy" than the Rutlands though.  The 5/8" rutland stays pretty thick whereas the flat Cotronics one would pancake down to nothing.  
    Good to know. However, OP’s Large is fine, trouble with Medium only.
    canuckland
    · Share on FacebookShare on Twitter
  • CouplesCaddy
    CouplesCaddy Posts: 9
    Thanks so much guys, i didnt realize this was anything more than just buy the rutland and install it. Upon further googling there is a flat gasket which i definitely do not have. i just got excited and bought a spool as we have 5 eggs (4 different homes) in my family and i would just upgrade them all. Now it appears im the clown who didnt do their research and have to rebuy the flat type. Thanks for the insight guys! I was wondering how i was the first one to have this issue.  I do a lot of smoking with marinades so i do a lot of burndowns and need something better than the std junk gasket ive been using
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,758
    CouplesCaddy said:
    Thanks so much guys, i didnt realize this was anything more than just buy the rutland and install it. Upon further googling there is a flat gasket which i definitely do not have. i just got excited and bought a spool as we have 5 eggs (4 different homes) in my family and i would just upgrade them all. Now it appears im the clown who didnt do their research and have to rebuy the flat type. Thanks for the insight guys! I was wondering how i was the first one to have this issue.  I do a lot of smoking with marinades so i do a lot of burndowns and need something better than the std junk gasket ive been using
    The spool you want is #720......5/8" flat.  It's about $75 for 150'.  Should be enough to do about 25 large BGEs.
    · Share on FacebookShare on Twitter
  • CouplesCaddy
    CouplesCaddy Posts: 9
    stlcharcoal said:

    The spool you want is #720......5/8" flat.  It's about $75 for 150'.  Should be enough to do about 25 large BGEs.
    Thanks Stlcharcoal, i don't see it on amazon - just the rope type in 5/8", does anybody have a link for the one I need?
    · Share on FacebookShare on Twitter
  • alaskanassasin
    alaskanassasin Posts: 8,898

     Do your own research that this is what you want but he has Rutland 5/8" tape 157' roll for $73.50 free shipping


    South of Columbus, Ohio.


    · Share on FacebookShare on Twitter
  • RRP
    RRP Posts: 26,451
    edited March 2020
    CouplesCaddy said:

    Thanks Stlcharcoal, i don't see it on amazon - just the rope type in 5/8", does anybody have a link for the one I need?
    Don't make this more difficult for yourself!  - send me an email at:
    r o n . p a t @ c o m c a s t . n e t
    Just take out the spaces!
    Or simply send me a message on this forum.
    Re-gasketing the USA one yard at a time 
    · Share on FacebookShare on Twitter
  • GATraveller
    GATraveller Posts: 8,207
    You should direct message @rrp He'll get you taken care of easy peasy.

    "Social media gives legions of idiots the right to speak when they once only spoke at a bar after a glass of wine, without harming the community [...] but now they have the same right to speak as a Nobel Prize winner. It's the invasion of the idiots."
                                                                                  -Umberto Eco

    2 Large
    Peachtree Corners, GA
    · Share on FacebookShare on Twitter
  • hoosier_egger
    hoosier_egger Posts: 6,808
    And he'll even provide instructions. Can't get much simpler
    ~ John - Formerly known as ColtsFan  - https://www.instagram.com/hoosier_egger
    XL BGE, LG BGE, Med BGE, BGE Chiminea, Ardore Pizza Oven
    Bloomington, IN - Hoo Hoo Hoo Hoosiers!

    · Share on FacebookShare on Twitter
  • TN_Egger
    TN_Egger Posts: 1,120
    just don't forget to send him a check!
    Signal Mountain, TN
    · Share on FacebookShare on Twitter
  • CouplesCaddy
    CouplesCaddy Posts: 9
    @RRP, just sent you an email.  Thanks so much for the help everybody!
    · Share on FacebookShare on Twitter
  • stlcharcoal
    stlcharcoal Posts: 4,758
    CouplesCaddy said:
    stlcharcoal said:

    The spool you want is #720......5/8" flat.  It's about $75 for 150'.  Should be enough to do about 25 large BGEs.
    Thanks Stlcharcoal, i don't see it on amazon - just the rope type in 5/8", does anybody have a link for the one I need?
    https://www.amazon.com/Rutland-720-Grapho-Glas-Gasket-Spool/dp/B000HE8KNI

    Just google "Rutland 720"
    · Share on FacebookShare on Twitter
  • llrickman
    llrickman Posts: 654
    Just put the rutland on my Large. its not the prettiest but it sure is effective
    2 LBGE
    Digi Q
    green Thermapen
    AR

    Albuquerque, NM
    · Share on FacebookShare on Twitter
  • RRP
    RRP Posts: 26,451
    It’s not difficult to do, but if you want to do it correctly so that it will last for many years and seal properly then there are some right and wrong ways...but why should I say that? LOL...

     6,520 reasons in 18 years, maybe???
    Re-gasketing the USA one yard at a time 
    · Share on FacebookShare on Twitter
  • PigBeanUs
    PigBeanUs Posts: 932
    edited November 2020
    I am fairly sure I actually put the first rutland on an egg, with their cement. 

    But I am dead certain that a couple months later I was the first to use permatex to adhere it. 

    And it’s still on, with minimal prep, like 18 years later. 

    I scraped off my old original felt one, with a paint scraper. 

    Wire brushed it clean, and tried a rutland with their stove cement. The ceramic wicks away the water, which is required for the cure. I started getting loose spots. 

    So I went to the hardware store and bought some gasket maker   

    I tore off the rutland in one yank. It still had the rutland cement adhered to it. 

    Squirted a zig-zag of the permatex on the rim and slapped the gasket back down. No trowels. No effort

    That was 18 or 19 years ago 

    I don’t know when our intrepid rutland salesman switched over to permatex as well, but it really is much better. 

    There was one guy who made the gasket itself from permatex. After all, it is a “gasket maker” sealant. 

    He cleaned the rim, squeezed an even thickness of permatex around the rim, put a couple spacers down so it wouldn’t squish out when he shut the lid, laid plastic wrap down, and shut the lid. 

    That’s what gave me the idea to just use permatex as the adhesive. 

    Your possible future lung cancer from the rutland and permatex is not my responsibility. Hahaha
    · Share on FacebookShare on Twitter
  • RRP
    RRP Posts: 26,451
    PigBeanUs said:
    I am fairly sure I actually put the first rutland on an egg, with their cement. 

    But I am dead certain that a couple months later I was the first to use permatex to adhere it. 

    And it’s still on, with minimal prep, like 18 years later. 

    I scraped off my old original felt one, with a paint scraper. 

    Wire brushed it clean, and tried a rutland with their stove cement. The ceramic wicks away the water, which is required for the cure. I started getting loose spots. 

    So I went to the hardware store and bought some gasket maker   

    I tore off the rutland in one yank. It still had the rutland cement adhered to it. 

    Squirted a zig-zag of the permatex on the rim and slapped the gasket back down. No trowels. No effort

    That was 18 or 19 years ago 

    I don’t know when our intrepid rutland salesman switched over to permatex as well, but it really is much better. 

    There was one guy who made the gasket itself from permatex. After all, it is a “gasket maker” sealant. 

    He cleaned the rim, squeezed an even thickness of permatex around the rim, put a couple spacers down so it wouldn’t squish out when he shut the lid, laid plastic wrap down, and shut the lid. 

    That’s what gave me the idea to just use permatex as the adhesive. 

    Your possible future lung cancer from the rutland and permatex is not my responsibility. Hahaha
    LOL hey Jeff, welcome back! 
    Going to stick around with this new moniker or revert to your old ones?
    Re-gasketing the USA one yard at a time 
    · Share on FacebookShare on Twitter

Categories