Skip to content
  • Register
    • Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
    Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
    Share your photos by tagging us and using the hashtag #BigGreenEgg.

    Want to see how the EGG is made? Click to Watch

    Just had new egg delivered. Have a question. Lid doesn't seem centered.

    Posts: 129
    in EggHead Forum
    I just got back early from a trip to find my wife 'surprised' me with a BGE that was delivered to our house.  There was something that I noticed right away that struck me as odd and I wanted to be sure before I do anything with it.  The lid doesn't seem centered (front to back).  The front of the top (lid) seems to be slightly recessed back from the bottom by about 1/4".  So in the front the top is slightly back from the bottom and in the rear, the top hangs slightly over the bottom.  The gaskets however seem to line up fairly well, but I'm not sure if that's because the gaskets were simply placed where the two pieces connect.  I realize that the important thing is whether or not it leaks air (which can be tested by doing the dollar bill test) but I don't even want to use this thing if there's any defect with the assembly.  I will try to post a picture if needed, but in the meantime, what should I do (if anything)?
    XL BGE Owner Since September 2015 - So expect a lot of newbie questions and please go easy on me :-)
    · Share on FacebookShare on Twitter

    Welcome!

    It looks like you're new here. Sign in or register to get started.
    Sign In
    Register

    Comments

    • Posts: 378
      Call dealer to fix the under bite. They should line up.
      George Foreman? Who? 
      Tim C. Panama City, Fl. 
      Large, Minimax-soon
      · Share on FacebookShare on Twitter
    • Posts: 683
      I think mine has a SLIGHT underbite. Has never hurt me. You can likely tweak it to better align but I wouldn't let that stop me from an inaugral cook.  Post a pic if you can. Lots of eggsperts will advise.
      LBGE, AR.  Lives in N.E. ATL
      · Share on FacebookShare on Twitter
    • Posts: 683
      But be advised, a lot of the local heroes will be tanked in a few hrs. Lol
      LBGE, AR.  Lives in N.E. ATL
      · Share on FacebookShare on Twitter
    • Posts: 1,122
      I agree with @tcracing.
      Take note of how they realign the dome to the base. Chances are, you will need to realign again later down the road.  ;)
      XL BGE, 22" Weber Red Head, Fiesta Gasser .... Peoria,AZ
      · Share on FacebookShare on Twitter
    • Posts: 683
      Let's hope the dealer knows how to.  I mean they set it up this way.. Just sayin.
      LBGE, AR.  Lives in N.E. ATL
      · Share on FacebookShare on Twitter
    • Posts: 26,227
      Welcome aboard! It is only natural to think that your new $800 BGE should be perfect, but in all honesty 1/4" is no great shakes and IMHO is nothing to worry about. These bases and domes are cast in mass separately. They are not cast as a single piece and then cut apart, nor are they fine China from a jewelry store. If you feel better then by all means contact your dealer on Monday and see what they say and how they respond to your concern. It may reveal how your dealer will treat you in the future when you have warranty claims.
      Re-gasketing the USA one yard at a time!
      · Share on FacebookShare on Twitter
    • Posts: 20,935
      edited August 2015
      Also be warned continued heating and cooling cycles will affect this.

      I recommend cooking on it for a few weeks.  If at that point it still bothers you, then call the dealer to have them realign.

      If you are worried call the dealer to let them know your issue and if in a few weeks it still bothers you then you will call them back to fix it.

      Also, give your wife a big hug and tell her thank you!!  Awesome surprise, don't obsess over the alignment.

      Don't tell your problems to people.  80% of people don't care and 20% are glad you have them.


      · Share on FacebookShare on Twitter
    • Posts: 2,158
      Agree with everyone here, but you know what ... you guys spent alot of coin, have them come out and make the adjustments.

      Then watch how they do it, for future reference.
      I've slow smoked and eaten so much pork, I'm legally recognized as being part swine - Chatsworth Ca.
      · Share on FacebookShare on Twitter
    • Posts: 129
      I forgot to mention it's an XL. Are there not any screws or something I might be able to simply tighten or loosen to align it properly?
      XL BGE Owner Since September 2015 - So expect a lot of newbie questions and please go easy on me :-)
      · Share on FacebookShare on Twitter
    • Posts: 129
      It's kind of hard to see how bad the misalignment is from these pictures but here they are anyway.,,
      XL BGE Owner Since September 2015 - So expect a lot of newbie questions and please go easy on me :-)
      · Share on FacebookShare on Twitter
    • Posts: 481
      Should line up but does it pass the dollar bill test?
      · Share on FacebookShare on Twitter
    • Posts: 1,122
      edited August 2015
      Yea, have the dealer fix that. My XL has an underbite about 1/16" yours looks closer to 3/8'".
      I'll try & fix my issue when the felt gasket goes bad. I have a @RRP special ready when needed.
      XL BGE, 22" Weber Red Head, Fiesta Gasser .... Peoria,AZ
      · Share on FacebookShare on Twitter
    • Posts: 10,458
      edited August 2015
      Really hard to tell by the pic but it doesn't look too terrible.  My large has had 1/4" offset for several years. Unless your gasket is hanging inside the opening you are good to go.  
        I've got the same gasket as you and I'm on year #5 on my large. So in short words unless the gasket is hanging inside the base or dome  don't sweat it. You have several yrs of use ahead of you.  

      -----------------------------------------

      analyze adapt overcome

      2008 -Large BGE. 2013- Small BGE and 2015 - Mini. Henderson, Ky.
      · Share on FacebookShare on Twitter
    • Posts: 667
      I have had an under bite for a couple of years now, no biggie.  Passes the dollar test, and leaks no smoke, so no concerns here either..  obviously your call since it new, but like others started above, might want to use it for a while and see how it goes while informing the dealer to make them aware
      Large BGE 2011, XL BGE 2015, Mini Max 2015, and member of the "North of the Border Smokin Squad" Canadian Outdoor Chef from London, Ontario, Canada

      https://www.flickr.com/photos/monty77/
      · Share on FacebookShare on Twitter
    • Posts: 4,232
      Normal

      Welcome to the bane of the over/under Egger's eggsistance! 
      New Albany, Ohio 

      · Share on FacebookShare on Twitter
    • Posts: 2,319
      edited August 2015
      My XL has a similar looking underbite. The seal is good with no leaks and the gasket isn't frying, so I'm leaving it be.
      Living the good life smoking and joking
      · Share on FacebookShare on Twitter
    • Posts: 297
      My large has a slight underbite - all my fault as I put the egg together myself and in my excitement to finish her up I did notice the 'problem' I was creating.

      As others have said, if you are not leaking, no problem. However, if it troubles you to much, take a look at how level the band on the lower half of your egg is front to back.

      I would guess that the band sits higher in the front and you have a slight pitch towards the back. This forces the hinge mechanism to be lower than intended thus creating the issue where the dome sits further back... underbite.
      Bloomfield Hills, MI | LGBE : AR R & B Oval Combo w/Extender and Sliding D Grid : Kick Ash Basket : Smokeware Cap : Smobot Beta
      · Share on FacebookShare on Twitter
    • Posts: 456
      Mine's offset to the left. Over 5 years, I didn't notice until I saw this topic and checked. Unless it isn't a ggod seal don't worry about it.
      · Share on FacebookShare on Twitter
    • Posts: 890
      edited August 2015
      Not a perfect science...I actually have dome band depth from rim less than bottom and get perfect alignment. Wouldnt worry much now and after  a few cooks play with it. Bands higher lower.etc. consistently AROUND entire rim more important than depth from rim.

      I would much rather be able to say I was glad I did than wished I had........

      XL owner and purveyor of pallette perfection...

      Homosassa....Mecca of Florida

      · Share on FacebookShare on Twitter
    • Posts: 1,750
      Yeah, mine is off to the right and I have never messed with it.  I assembled it myself and heat caused the shift in position over time, I think. Been that way for 3 years.  

      In in your case, I'd call the dealer and have them reposition it.  Keep in mind, that it might shift back out of alignment with use.  
      Dave - Austin, TX
      · Share on FacebookShare on Twitter
    • Posts: 4,232
      edited August 2015


      Just be sure to tighten you band bolts in 30 days. Seriously. 
      New Albany, Ohio 

      · Share on FacebookShare on Twitter
    • Posts: 129
      Ok, So I just decided to do the dollar bill test.  It holds the bill moderately snug in the front, a little loose along the sides and completely loose in the back.  I'm definitely not happy about this and while I'm sure I can follow the instructions I've seen in the various 'underbite' threads on how to adjust the bands and what not, I think the dealer ought to take care of this.  The last thing I want to do is break something or screw something up and have them tell me it's not covered because of what I did.  I'm a little bummed about this and I don't want my wife to even know because I don't want her to be disappointed either.
      XL BGE Owner Since September 2015 - So expect a lot of newbie questions and please go easy on me :-)
      · Share on FacebookShare on Twitter
    • Posts: 26,227
      edited August 2015
      Tier1Terrier said:
      Ok, So I just decided to do the dollar bill test.  It holds the bill moderately snug in the front, a little loose along the sides and completely loose in the back.  I'm definitely not happy about this and while I'm sure I can follow the instructions I've seen in the various 'underbite' threads on how to adjust the bands and what not, I think the dealer ought to take care of this.  The last thing I want to do is break something or screw something up and have them tell me it's not covered because of what I did.  I'm a little bummed about this and I don't want my wife to even know because I don't want her to be disappointed either.
      Good idea. Actually what you describe is proof positive that the planes of your dome and base are out of whack. To fix it you or your dealer will need to loosen the band bolts and press downward forcing the planes of the two ceramic parts to shift and that way match up. Then the bolts will need to be re-tightened. Yes let your dealer solve the issue. If you didn't resolve the loose backside then your gasket would soon be history due to escaping gases and heat.
      Re-gasketing the USA one yard at a time!
      · Share on FacebookShare on Twitter
    • Posts: 129

      Crisis averted!!!  I called this morning and spoke to Dewayne at BGE HQ Customer Service.  He was extremely helpful and guided me through the steps to level out the top.  It was extremely simple to do, even for someone who didn't understand the way these things are put together.

      So basically here's what was the problem and what I did.  The first problem was that the lower band was not wrapped around evenly - it was lower in the rear than in the front.  He explained to me that the lower band should come right up to the edge of the lower gasket all the way around the lower half.  So I loosened the carriage bolt on the lower rear band and GENTLY tapped along the band using a block of wood and a rubber mallet until the band was placed evenly around the whole bottom.  Then I tightened the band.  From that point, the underbite had improved significantly, but there was still a bit of unevenness along the planes where the gaskets met and it still did not pass the dollar bill test.  In fact, the gap on the rear side between the gaskets was slightly worse, but I wasn't worried because I knew there were a couple more steps to

      Next step was to adjust the front to back placement to fine tune the sitting of the top to the bottom.  There are two slotted acorn nuts on the top part of the hinge (above the spring) on both sides of the top that needed to be loosened so that I can 'wiggle' the top into a centered position.  So I loosened all 4 nuts, wiggled it into position, then tightened.  Now the top was centered properly (no under or overbite), but there was still unevenness on the plane of contact - in other words, it still failed the dollar bill test.

      The last step was to somewhat repeat the first step (loosening the carriage bolt) except for the upper band.  Wherever there was the largest gap between the two gaskets, I GENTLY tapped the band upward which essentially pushed the lid downward by it's own weight.  Once I saw that the upper band was positioned in such a way that the entire top part of the egg sat nicely and evenly on the bottom, I tightened the carriage bolt of the top band and vuala!  It was fixed.  Dollar bill test passed all the way around the egg.  No more underbite (or overbite).

      I'm happy as a clam!

      XL BGE Owner Since September 2015 - So expect a lot of newbie questions and please go easy on me :-)
      · Share on FacebookShare on Twitter
    • Posts: 5,234
      I am glad you got it fixed. My first egg was aligned perfectly, but my second one was not. I couldn't stand it. I worked and worked on it until I get it lined up. 

      Louisville, GA - 2 Large BGE's
      · Share on FacebookShare on Twitter
    • Posts: 254
      Glad you got it worked out.  After you cook on it a few times check all those bolts and make sure they're still snug.
      XL BGE
      Plano, TX
      · Share on FacebookShare on Twitter
    • Posts: 87
      Bravo!  
      · Share on FacebookShare on Twitter
    • Posts: 569
      My XL was delievered and assembled perfect.   within a couple weeks, it had developed an underbite.    The guys from the dealer came out and fixed it by adjusting the lower band UP which pushed the lid Forward.    
      It slipped back down again and I'm back to underbite.

      I would LOVE to design a proper hinge for this, to take the weight and allow for adjustment.
      · Share on FacebookShare on Twitter

    Welcome!

    It looks like you're new here. Sign in or register to get started.
    Sign In
    Register

    Welcome!

    It looks like you're new here. Sign in or register to get started.
    Sign In
    Register

    Quick Links

    Categories