Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Want to see how the EGG is made? Click to Watch
Facebook | Twitter | Instagram | Pinterest | Youtube | Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Want to see how the EGG is made? Click to Watch
How to adjust Dome underbite?
Larrymac
Posts: 103
This is after new gasket was applied. Seal with a dollar bill is very tight in the back, but too loose with no friction whatsoever. You can see the actual underbite -- top of dome facing the front is maybe 1/8 to 1/16 withdrawn inside from being flush with the bottom. Obviously the top back is about the same distance to far back from being flush with the bottom.
What bolts or nuts on the back need to be loosened to make the adjustment? Do I need to put a zip tie to maintain the spring?
What bolts or nuts on the back need to be loosened to make the adjustment? Do I need to put a zip tie to maintain the spring?
Comments
-
Be sure to either zip tie top and bottom together or remove springs before you start adjusting. Don't ask me how I know...They/Them
Morgantown, PA
XL BGE - S BGE - KJ Jr - HB Legacy - BS Pizza Oven - 30" Firepit - King Kooker Fryer - PR72T - WSJ - BS 17" Griddle - XXL BGE - BS SS36" Griddle - 2 Burner Gasser - Pellet Smoker -
This a particularly vexing problem. I'm on my second set of rings, since I couldn't adjust the old ones in. I did get the second set to align, but on a recent hot cook, it jumped to underbite. I fixed it by loosening up the rings, pulling the bottom ring as high as it would fit on the base, and torquing the flat part of the spring assembly with an oversized crescent wrench. I'm not sure if this is the right way to do it, but it's what worked for me. There don't seem to be any particular bolts that will pull it one way or another. All the advice I've read just says loosen the bolts and push the top into place. YMMV. Good luck.Kemah, TX
-
jllbms said:
This a particularly vexing problem. I'm on my second set of rings, since I couldn't adjust the old ones in. I did get the second set to align, but on a recent hot cook, it jumped to underbite. I fixed it by loosening up the rings, pulling the bottom ring as high as it would fit on the base, and torquing the flat part of the spring assembly with an oversized crescent wrench. I'm not sure if this is the right way to do it, but it's what worked for me. There don't seem to be any particular bolts that will pull it one way or another. All the advice I've read just says loosen the bolts and push the top into place. YMMV. Good luck.
-
40 views 2 responses . I know it's not a sexy post, but suppose there's not a definite answer to this which is why responses are limited.
I pretty much did what you did or said just before I got your response . Put zip ties to maintain the springs.
I loosened all the hinge bolts and loosened the top band. Then sort of wrestled the top lid over the 1/8" I needed to line the the top with the bottom.
Dollar bill was now a tighter fit all the way around. Tightened all bolts and bands. Removed zip ties.
Hopefully it stays where it is. Can't understand how yours moved after a cook???? Thanks for your response . -
Likely the bands expanded and slipped - this was at 700 - 800 range. I was doing a pizza cook and it got too hot. No more high temp pizza cooks! If you'll search on underbite here in the forum, you'll get a lot more information.Kemah, TX
-
Does an underbite make that much of a difference? I think I tried to correct mine a few times, then gave up. I can't say that it affects anything that I have been able to notice.#1 LBGE December 2012 • #2 SBGE February 2013 • #3 Mini May 2013A happy BGE family in Houston, TX.
-
Probably equally psychological, but the misalignment does expose more of the gasket to direct heat, leading to early wear.Kemah, TX
-
If smoke is not billowing out I would not screw with it.Salado TX & 30A FL: Egg Family: 3 Large and a very well used Mini, added a Mini Max when they came out (I'm good for now). Just given a Mini to add to the herd.
-
-
True - with those wimpy gaskets! Rutlands laugh at those issues!jllbms said:Probably equally psychological, but the misalignment does expose more of the gasket to direct heat, leading to early wear.Re-gasketing the USA one yard at a time -
caliking said:
Does an underbite make that much of a difference? I think I tried to correct mine a few times, then gave up. I can't say that it affects anything that I have been able to notice.
-
I have a slight underbite but I pass the bill test. So I just left it.....
-
Miked125 said:
I have a slight underbite but I pass the bill test. So I just left it.....
-
With the underbite I could push the dollar bill thru the front with no resistance. The back side, could not pull the bill out.
After the adjustment, decent friction with the bill all the way around.
Categories
- All Categories
- 184K EggHead Forum
- 16.1K Forum List
- 461 EGGtoberfest
- 1.9K Forum Feedback
- 10.5K Off Topic
- 2.4K EGG Table Forum
- 1 Rules & Disclaimer
- 9.2K Cookbook
- 15 Valentines Day
- 118 Holiday Recipes
- 348 Appetizers
- 521 Baking
- 2.5K Beef
- 90 Desserts
- 167 Lamb
- 2.4K Pork
- 1.5K Poultry
- 33 Salads and Dressings
- 322 Sauces, Rubs, Marinades
- 548 Seafood
- 175 Sides
- 122 Soups, Stews, Chilis
- 40 Vegetarian
- 103 Vegetables
- 315 Health
- 293 Weight Loss Forum