Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.

Want to see how the EGG is made? Click to Watch

Digiq dx

Green For Sure
Green For Sure Posts: 13
edited November -0001 in EggHead Forum
Just bought a Digiq dx yesterday. Smoking a boston butt and it is running like a champ--spot on. Quick question, will it work in the rain?

Comments

  • Fidel
    Fidel Posts: 10,172
    yes, but, I always put an overturned clear/opaque plastic tub over it so I can still see the display.

    I try to keep the power cord connections away from water if at all possible so as not to trip a GFCI circuit and lose power.
  • Grandpas Grub
    Grandpas Grub Posts: 14,226
     
    Green For Sure wrote:
    will it work in the rain?

    Of course it will, the question is for how long.

    Water and electronics... Even though they say water proof/resistant why take a chance. The points on the unit that have plugs are not water proof or resistant.

    There have been some posts that folks have made some really nice modified rubber/plastic tubs to hold the DigiQ & Stoker units some have even gone to the extent of putting 90° PCV elbows for the wires to exit the tubs.

    I have some bread bags around and use one of those when there is a chance of snow or rain coming down. The exit part of the bag is folded down under the controller so there will be no capillary action moisture moisture.

    GG
  • asianflava
    asianflava Posts: 313
    I put a zip lock bag over mine.
  • srq2625
    srq2625 Posts: 262
    Yeah, electronics and water don't play well together. Since it rains quite often in Virginia, I had to come up with a solution to cope with the conditions. I was inspired by some of those posts and this is what I came up with:

    1. This is all the gear I use with my Stoker
    1222445675_4Z4YB-M.jpg
    What's significant here is the pair of 135° elbows with a very short piece of Schedule 40 PVC pipe stuck in one end (no glue necessary), the 4 rubber gaskets, and the two locking rings. Stick a gasket on the elbow, stick the elbow in the hole of the box (there's two holes, one on each side of the box), add another gasket, and the locking ring. Repeat for the other side.

    I elected to use the 135° elbows because I couldn't easily get the probe jacks and the female end of the extention cord through a 90° ... and I did try. The 135° do a really good job of keeping the wet stuff out.

    2. Here's the box with everything set up. There are two connections out the back of the Stocker (pit probe and fan) and two out the front (two meat probes). Beside it are the WIFI connector and on the other side, my thermopen.
    1222443649_8ZVxE-M.jpg

    3. With the lid on
    1222443009_F5yhV-M.jpg

    4. Don't know how tolerant the fan might be soooo. Oh, and this will help protect the bottom vent/fan from strong winds as well.
    1222443280_DJn3q-M.jpg

    5. Speaking of strong winds, just to make sure the lid doesn't fly away (it's not real secure), I use a custom device I spared no expence in obtaining :)
    1222445404_BsioH-M.jpg

    6. After the cook is finished, need to put things away. The two paper towels are to keep the smoke smell from enhancing the indoors (some people are a little sensitive to too much smoke). The box is just large enough to hold everything without being too large.
    1222445511_nxbew-M.jpg
  • Thank you everyone! Great suggestions.

    Regards,
    Brandon
  • SomedayMommy
    SomedayMommy Posts: 199
    VERY impressive indeed! It rains a lot here in Ohio, too. I am going to have to make one of these...