Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing kamado recipes by following Big Green Egg to Experience our World of Flavor™ at:
Want to see how the EGG is made? Click to Watch
Facebook | Twitter | Instagram | Pinterest | Youtube | Vimeo
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Share your photos by tagging us and using the hashtag #BigGreenEgg.
Want to see how the EGG is made? Click to Watch
Brisket help
Options
jwc6160
Posts: 218
doing a brisket this weekend and nervous about. I have done one prior and got lucky. It turned out great with minimal effort. I was actually sick and my wife babysat it for me. I didn’t have a probe at the time and just eyeballed it. Anyway, I’m more prepared this time so I’m bound to screw it up. Where do I place the probe? In the flat part or the tip/thick end? I am doing a whole packer from Costco. Do I pull when the flat end hits 202 or the thick end. Thanks for any help/tips.
Comments
-
Place the temperature probe in the thickest part of the flat. Pull when it probes with minimal resistance.....temp will in the 200 ballpark of the flat. The "thick end" or point will take care of itself because of the higher fat content.
"Social media gives legions of idiots the right to speak when they once only spoke at a bar after a glass of wine, without harming the community [...] but now they have the same right to speak as a Nobel Prize winner. It's the invasion of the idiots."
-Umberto Eco
2 Large
Peachtree Corners, GA -
thanks
-
As above, go with the feel in the thickest part of the flat. Temperature is only a guide for when to start the finish-line "feel" process.
Good eyeball to nail a brisket finish...if you had that kind of success right out of the gate then I wouldn't change it up.Louisville; Rolling smoke in the neighbourhood. # 38 for the win. Life is too short for light/lite beer! Seems I'm livin in a transitional period. -
Obviously you already figured out the secret is to just let your wife cook it.
NOLA -
Probably should have asked this before but if I want to stay around 250-275 is that dome or probe temp?
-
Just pick if you want to go by dome or probe temperature and stick with it. I use the grid temperature. I do notice that they eventually settle within 10 degrees of each other.Pittsburgh, PA. LBGE
-
Right now I’m 235 grid and almost 300 dome. That’s a pretty big difference. The probe isn’t terribly close to the meat either.
-
You can’t fake a high temp. So over time your whole cooking area will trend toward 300. You might close your airflow down just a little.
XXL BGE, Karebecue, Klose BYC, Chargiller Akorn Kamado, Weber Smokey Mountain, Grand Turbo gasser, Weber Smoky Joe, and the wheelbarrow that my grandfather used to cook steaks from his cattle
San Antonio, TX
-
I notice that my grid and dome temperature are very different at the start. After an hour or so, they should get close to each other. I don’t know how long you have been running or what your dampers are set to. Your dome or grid probe could need to be recalibrated. Like I said before, pick one and kind of ignore the other. If not, you will needlessly stress yourself out.Pittsburgh, PA. LBGE
Categories
- All Categories
- 182.7K EggHead Forum
- 15.7K Forum List
- 459 EGGtoberfest
- 1.9K Forum Feedback
- 10.3K Off Topic
- 2.2K EGG Table Forum
- 1 Rules & Disclaimer
- 9K Cookbook
- 12 Valentines Day
- 91 Holiday Recipes
- 223 Appetizers
- 516 Baking
- 2.4K Beef
- 88 Desserts
- 163 Lamb
- 2.4K Pork
- 1.5K Poultry
- 30 Salads and Dressings
- 320 Sauces, Rubs, Marinades
- 543 Seafood
- 175 Sides
- 121 Soups, Stews, Chilis
- 35 Vegetarian
- 100 Vegetables
- 313 Health
- 293 Weight Loss Forum