Big Green Egg - EGGhead Forum - The Ultimate Cooking Experience...
Are you happy it’s finally National BBQ Month? While we like to BBQ year round, May is our favorite because the whole country is celebrating delicious food. If you’re new to cooking BBQ on your EGG, check out our Smoking Basics Publication...if not, proceed to some of our favorite recipes! We love Dr. BBQ’s Coffee Rubbed Brisket, Famous Dave’s Sticky Ribs and Virginia Willis’ Pulled Pork. Pair with this cheesy favorite for a winning way to start off May!

Big Green Egg headquarters has moved - come visit our new showroom and check out the museum and culinary center too! 3786 DeKalb Technology Parkway, Atlanta, GA 30340

Mickey T's rings

bbqjewbbqjew Posts: 34
edited 6:35PM in EggHead Forum
does anyone that has a set of these, know the diameters of each of the holes? I have a stoker (that is in storage as well as most of my belongings) but am looking to do a low and slow, and thought that i might try and make a set of these to help out with the temperature control.

Thanks in advance for any help.
Mark
·

Comments

  • Mark:

    I have a set for the Large and for the Small. As it's the middle of the night, I can't get to them right now. If no one can help you, shoot me an e-mail to remind me and I'll get the dimensions for you.

    Judy in San Diego
    Judy in San Diego
    ·
  • Richard FlRichard Fl Posts: 7,820
    Does this help?

    BGE, Rings, Mickey "T"



    MICKEYTRINGS.jpg



    Recipe Type
    Equiptment/Toys

    Recipe Source
    Source: BGE Forum, Mickey "T"

    02/13/07--Richard,

    It's not a hard wood it's a plywood.

    Finland birch or maple. $3.25 a sq. Ft. 5/8" thick.

    Increments were in 1/8 ths

    Mick

    Mick Tinnon

    President, GC Dies

    Warrenville, Il

    2009/10/05--- RRP--No problem - I took it (picture) and posted it years ago and when Mickey asked me for the access and I gave it to him to use. What some people might not know about Mickey is he and his BGE were featured in a Wall Street Journal article years ago about Chicagoans who have lodges up North and in this piece Mickey was shown egging in some deeeep snow one weekend he had gone up there by himself.
    ·
  • bbqjewbbqjew Posts: 34
    Thank you. I assume the rings start at 1/8 inch and work there way up.
    That helps. I will let you know how it works out.

    Mark
    ·
  • Are there some instruction on how to use them.
    ·
  • CobraCobra Posts: 110
    For those of us that haven't been around as long, what are they for?
    ·
  • Richard FlRichard Fl Posts: 7,820
    I have never seen them in person, but my understanding is that they go on top of the dome and instead of adjusting the vents you just change the tops until you get the air flow you need to maintain whatever temp.
    ·
  • RRPRRP Posts: 15,009
    BINGO - the only real problem is remembering to take them off when you open the lid - seriously - cauz they fall off! :laugh: Actually of my 11 rings I only ever use 3 of them and they allow you to lock on to 300 to 350 very easy.
    Ron
    Dunlap, IL
    ·
  • CobraCobra Posts: 110
    Nice, thats kinda what I thought they looked like they were for but wasnt sure. Thanks for answering so quickly.
    ·
  • RRPRRP Posts: 15,009
    just so you'll know the rest of the saga - Mickey then started playing around with the idea of an adjustable one and address the falling off issue! He made a couple prototypes he called a Wing.
    IMG_1983.jpg

    IMG_1716.jpg

    Then some wise-guys started pimping him that all he had created was a wooden daisy and he dropped the project and pretty much left this board for good. That was a shame as he was a good guy!
    Ron
    Dunlap, IL
    ·
  • I used the rings and most of the variations. When Mick 'retired' from ring making I started making my own.

    Ended up with this design which I have used for a number of years. NO falling off.

    Wave2.jpg

    Wavemk52.jpg

    Wavemk56.jpg

    And before you get your panties in a knot, MickT put his seal of approval on the idea.

    Spacey
    ·
Sign In or Register to comment.