Big Green Egg - EGGhead Forum - The Ultimate Cooking Experience...
We hope you had a hoppy Easter and are ready to spring into warm weather cooking mode! There’s nothing better than spending time outdoors with the sweet aroma of fresh cooked Ribs. Baseball season is also underway, so it's the perfect time to try out some chicken wing variations! We have Jamaican Jerk, Lemon Pepper, Fired-Up Wings and even a Whiskey Onion and Chicken Steak if wings aren't your thing. Bon appetit!



Big Green Egg headquarters has moved - come visit our new showroom and check out the museum and culinary center too! 3786 DeKalb Technology Parkway, Atlanta, GA 30340

Help on Table

mobbqmobbq Posts: 3
edited November -1 in EggHead Forum
I am going to start building a table to my new egg but am not experienced at woodworking. What is the best method to cut the hole for the egg to sit down in? I thought about a router but didnt know if that would work. Thanks
·

Comments

  • FidelFidel Posts: 10,168
    I use a jigsaw, then smooth it with a router roundover bit then sand it smooth.
    ·
  • mobbqmobbq Posts: 3
    Also any advise I would appreciate it. I am thinking about putting tile on the top for a nice surface but didnt know if that was hard to do. Thanks everyone
    ·
  • luis70458luis70458 Posts: 48
    0129090917-00.jpg
    ·
  • vidalia1vidalia1 Posts: 7,091
    I don't know if you have seen this site before:

    http://www.nakedwhiz.com/TableGallery/tables.htm

    great info & pictures
    ·
  • El GuapoEl Guapo Posts: 9
    Draw your circle on the top.

    Use a jigsaw and cut the circle out by cutting just inside the line. You will be left with a somewhat rough cut.

    Now sand to the line. This allows you to "sneak up" on the line and get a nice looking circle.

    You can then either round over the edges with sandpaper or use a router with a round over bit.

    Post pictures when done!
    ·
  • Davidg5700Davidg5700 Posts: 32
    I'd go with the jigsaw also. They make following a curve easy. If your jigsaw has the ability to adjust the blade angle, set it for straight up. This slows down the cut, but gives a much cleaner cut than a more aggressive angle. Just take it slowly and let the saw do the work.

    Best of luck ;)
    ·
  • To make the circle I used one of those 5 gallon paint stirrer sticks. I drilled 2 small holes in it at a distance of half of how big I wanted the hole to be. Then at the spot I wanted the center of the hole to be I put a nail through the hole and nailed it into the table and put a pencil in the other hole and drew the circle.
    ·
  • FidelFidel Posts: 10,168
    That works great!

    I just use a string to draw the radius. I put a screw in the center, then tie a pencil at 10.5" and draw a circle.

    Your idea sounds better and more stable.
    ·
  • That is a trick I learned on here, I just can't remember who posted it.
    ·
  • opodopod Posts: 41
    i'm terrible at woodworking myself and built a table last year. the way it was described to me and worked well is to lay some plank down as if you we not going to have a hole. then find your center point, put a nail there and tie a string to it, a pencil to the other end and draw your circle. use a jigsaw to cut out the hole. i would also make sure you get a countersink for the screws you use on the table as i learned the hard way when i split several planks trying to get the screws drilled all the way down.
    ·
  • Cpt'n CookCpt'n Cook Posts: 1,917
    I used a jigsaw too, I took it as an opportunity to use some of my nice old, obsolete, drafting tools to draw the circle.
    Compass.jpg
    ·
  • Panhandle SmokerPanhandle Smoker Posts: 3,018
    I used the dome for the template. Just pencil under the gasket as far as you can. It gave me about 3/8-1/2 inch clearance all around the Egg.
    ·
Sign In or Register to comment.