Big Green Egg - EGGhead Forum - The Ultimate Cooking Experience...
Get ready to turn up the heat as we dive into August. While there are only a few weeks left to perfect those tailgate recipes, summer isn’t over yet! Two things we’ll be making this month are Chile Rubbed Grilled Pork Chops and Bell Pepper Kabobs. Then, relax after a cookout with a cool dessert cooked on your EGG - Ice Cream Sandwiches! You can mix and match your favorite cookie flavors with ice cream flavors. Simple, yet delicious!

Big Green Egg headquarters has moved - come visit our new showroom and check out the museum and culinary center too! 3786 DeKalb Technology Parkway, Atlanta, GA 30340

Clean burn gone wrong. Help!

2»

Comments

  • GATABITESGATABITES Posts: 1,102
    @orthobear - thanks for the pics. Very descriptive. I will go this route when my gasket fails. 

    @rrp - i just wanted to know how difficult/simple the process was with removing the old and installing the Rutland. this post answered my questions. 
    XL BGE 
    Joe JR 
    Reisterstown, MD
  • OrthobearOrthobear Posts: 84
    No problem Gatabites. RRP's instructions were really easy to follow. The one question I have was whether or not I laid down enough permatex adhesive. I probably used about half of the tube. I'll take a picture tomorrow to see how it is.
    Houston, TX
  • BYS1981BYS1981 Posts: 2,060
    Clean burns are unnecessary imo.
  • FiremanyzFiremanyz Posts: 618
    When installing the rutland gasket does it only go on the bottom? I am needing to replace mine as it burned off during the last clean burn. Also it cracked my fire ring. Called yesterday to get a replacement.
  • RRPRRP Posts: 15,899
    Yes I always strongly suggest that it only goes on the bottom!
    Ron
    Dunlap, IL
  • itsmceitsmce Posts: 277
    @rrp - so, when the original gaskets wear out/crack/breakdown (whatever happens to them) and a replacement is in order, if the Rutland only goes on the bottom does that mean that the dome is gasket-free?
    Large (sometimes wish it were an XL) in KS
  • RRPRRP Posts: 15,899
    itsmce said:
    @rrp - so, when the original gaskets wear out/crack/breakdown (whatever happens to them) and a replacement is in order, if the Rutland only goes on the bottom does that mean that the dome is gasket-free?
    Yes - that is possible because when the Rutland is properly compressed or "bunched" back into itself then it becomes both wider and thicker and therefore no gasket is needed on the dome. I cover all that in the instructions I send along with whatever size gasket is purchased. It's just a service I have been providing to fellow eggheads for 12 years now. BTW numbers 1,237-9 shipped today.
    Ron
    Dunlap, IL
  • Janssen14Janssen14 Posts: 50
    I'll never do it again I think the food tasted different after I did it..
  • RRPRRP Posts: 15,899
    Janssen14 said:
    I'll never do it again I think the food tasted different after I did it..
    No need to draw a line in the sand! The build up of grease and smoke over a period of time will coat your dome and walls with some pretty bad looking junk. In time that will start to flake off on to your food and then you will really feel "the food tasted different"!
    Ron
    Dunlap, IL
  • OrthobearOrthobear Posts: 84
    After the 24hr setup I opened the dome to test out the new gasket and when I tugged at it a little it came right off. Any ideas what went wrong? Not enough permatex? Was the surface not clean enough? Any ideas on what I need to do next? Thanks in advance.
    Houston, TX
  • OrthobearOrthobear Posts: 84
    From the looks of it I probably spread the permatex too thin.
    image.jpg 2.2M
    Houston, TX
  • nolaeggheadnolaegghead Posts: 14,966
    Agree - spread thin it sets up fast. 
    ______________________________________________
    This is my signature line just so you're not confused.
    Large and Medium BGE, Kamado Joe Jr., smoker with a 5k btu AC, gas grill, fire pit, pack of angry cats, two turntables and a microphone, my friend.
    New Orleans, LA - we know how to eat 

  • OrthobearOrthobear Posts: 84
    @nolaegghead - is it ok to apply new permatex to the set permatex or do I need to clean that off first?
    Houston, TX
  • RRPRRP Posts: 15,899
    edited July 2014
    You know I have replied to all of your emails, but thanks for the picture! That gasket never even kissed that Permatex, much less got embedded in the fibers!
    Ron
    Dunlap, IL
  • nolaeggheadnolaegghead Posts: 14,966
    Orthobear said:
    @nolaegghead - is it ok to apply new permatex to the set permatex or do I need to clean that off first?
    I would scrape off the old stuff first.  Adhesives adhere better (mechanically) to scratched up porous surfaces - that's the reason you have to sand between coats of polyurethane. 
    ______________________________________________
    This is my signature line just so you're not confused.
    Large and Medium BGE, Kamado Joe Jr., smoker with a 5k btu AC, gas grill, fire pit, pack of angry cats, two turntables and a microphone, my friend.
    New Orleans, LA - we know how to eat 

  • Coach292Coach292 Posts: 28
    Just thought about this. Since a very high heat clean burn might damage the gasket ...if you lined the gasket with aluminum foil wouldn't that protect it? I've noticed I've gone through a lot of gaskets over the years. It was probably low quality gaskets and the any high temp burns I did for steak and pizzas.
  • RRPRRP Posts: 15,899
    Coach292 said:
    Just thought about this. Since a very high heat clean burn might damage the gasket ...if you lined the gasket with aluminum foil wouldn't that protect it? I've noticed I've gone through a lot of gaskets over the years. It was probably low quality gaskets and the any high temp burns I did for steak and pizzas.
    My experience with even HD aluminum foil is it will melt at high heat. Rather than try to protect a wimpy gasket switch to a 2,200 degree Rutland and never look back!
    Ron
    Dunlap, IL
Sign In or Register to comment.