Share your photos by tagging us and using the hashtag #BigGreenEgg.
Want to see how the EGG is made? Click to Watch
New Gasket & Dome Alignment - Two Questions
Here's the problem:: I've also noticed that the dome is set to the rear about 1/4". I think this might have happened when I broke the BGE down to place it into the table a year ago. Regardless, it is definitely set back and I believe the fit of the dome to the base was good before this is, so I doubt this is a roundness problem. All the bolts seem to be tight. What, if anything do I do about this?
Rear Fit .... Front Fit
Thanks to RRP I have a new Rutland gasket ready for installation I know the Rutland is to be installed on the base. Do I just remove the top gasket and clean the top edge of the dome?
Thank you for your help!
Steve
Comments
-
Never installed a Rutland, so take this for what it is worth. Given the Rutland is only going on the base, I'd install it first.Loosen the bands so the dome is free to be re-positioned in the right place. Watch it does not slip off the base. While someone is holding it in place (SWMBO tells me I am not to call her dead weight anymore) tighten the bands, alternating between dome and base once they get some grip. Allow the band position to align with the held in place dome, and all should be good.Delta B.C. - Whiskey and steak, because no good story ever started with someone having a salad!
-
swbouton said:My Large BGE is almost two years old and it looks as though I have just about cooked the original gasket off. Some of it is literally hanging from the top. A few days ago I smoked a pork butt. The smoke from the apple chunks made it even more clear the gasket was shot.
Here's the problem:: I've also noticed that the dome is set to the rear about 1/4". I think this might have happened when I broke the BGE down to place it into the table a year ago. Regardless, it is definitely set back and I believe the fit of the dome to the base was good before this is, so I doubt this is a roundness problem. All the bolts seem to be tight. What, if anything do I do about this?
Rear Fit .... Front Fit
Thanks to RRP I have a new Rutland gasket ready for installation I know the Rutland is to be installed on the base. Do I just remove the top gasket and clean the top edge of the dome?
Thank you for your help!
SteveRe-gasketing America one yard at a time. -
Thank you both for your advice. It sounds good and I'm anxious to get to it.
-
I replaced the gasket this morning. I followed all RRP's instructions but I went one step further by removing everything from the BGE first. After I removed the old gasket and wiped the BGE clean I installed the new gasket then restored all the parts.
It went well. The removal was far easier than expected. Much of the old gasket peeled right off. Next I scraped, then used the 3M drill attachment and finally the pumice stone.
I might have compressed the gasket a bit too much because the last quarter barely made it to the end.
I found the problem with the alignment - the band around the dome was not symmetrical. It was lower in front than in the rear. That was due to the over-tightened bolt which I will replace tomorrow.
Thank you for all your help.
Steve
-
...I might have compressed the gasket a bit too much because the last quarter barely made it to the end...Steve, glad it came out ok! BTW too late now, but in my instructions I had the sentences with this hint:
Take your gasket and fold it in half and mark the center with a piece of masking tape. Then do that again and mark those points as well so your gasket is now marked in quarter lengths. This pointer will be helpful as a point of reference of just how compressed your gasket should be in relation to where you are on the edge. Get it? 12:00 to 3:00 is one fourth, etc.
Ron
Re-gasketing America one yard at a time. -
If you are replacing the two band bolts (the ones that bend), they are Grade 5 carriage bolts. Not sure if they have them at the big box stores, but Ace should have them.PS, that lovely orange color goes away after a while.
I hate it when I go to the kitchen for food and all I find are ingredients!
MichaelCentral Connecticut -
RRP, Yes, I did that trick with the masking tape. The only answer has to be that I compressed too much between 6 and 9.
Carolina Q, I'm going to ACE tomorrow to get better bolts. S/S maybe? and I'm glad to hear that orange racing strip will disappear.
-
My dome is off as well, I figured I would fix it when I replaced my gasket. Gasket is hanging from the dome now, guess it's time when it warms up...They/Them
Morgantown, PA
XL BGE - S BGE - KJ Jr - HB Legacy - BS Pizza Oven - 30" Firepit - King Kooker Fryer - PR72T - WSJ - BS 17" Griddle - XXL BGE - BS SS36" Griddle - 2 Burner Gasser - Pellet Smoker -
swbouton said:and I'm glad to hear that orange racing strip will disappear.Re-gasketing America one yard at a time.
-
swbouton said:Carolina Q, I'm going to ACE tomorrow to get better bolts. S/S maybe? and I'm glad to hear that orange racing strip will disappear.https://www.tessco.com/yts/customerservice/techsupport/whitepapers/pdf/bolt_grade.pdfDoes it matter? Beats me. My original bolts are over 4 years old and are still fine. If I ever have to replace them, I will buy the same type. Grade 5 galvanized, as I recall.
I hate it when I go to the kitchen for food and all I find are ingredients!
MichaelCentral Connecticut
Categories
- All Categories
- 182.7K EggHead Forum
- 15.7K Forum List
- 459 EGGtoberfest
- 1.9K Forum Feedback
- 10.3K Off Topic
- 2.2K EGG Table Forum
- 1 Rules & Disclaimer
- 9K Cookbook
- 12 Valentines Day
- 91 Holiday Recipes
- 223 Appetizers
- 516 Baking
- 2.4K Beef
- 88 Desserts
- 163 Lamb
- 2.4K Pork
- 1.5K Poultry
- 30 Salads and Dressings
- 320 Sauces, Rubs, Marinades
- 543 Seafood
- 175 Sides
- 121 Soups, Stews, Chilis
- 35 Vegetarian
- 100 Vegetables
- 313 Health
- 293 Weight Loss Forum