Ribs help

sppatel · January 4

Hi, I recently purchased an egg and I'm struggling with being able to make great ribs. Both times I smoked at 225 (dome), rubbed with mustard and a dry rub. The first time I took the 2-1-1 approach and the ribs had great flavor but they seemed a little tough even though they had a perfect smoke ring and white center. The second time I took the 2-2-1 approach. This time I don't think the rub penetrated the meat too much and once again where tough. I had again a good smoke ring, but many of the ribs had a grey (not white) center. Also I can never seem to get it to pass the bounce test where I bounce the ribs to get it to crack.

Any advice on what to try next? Any help would be appreciated.

henapple · January 4

Cook them till they pass the test. Every time I've gone wrong on pork it was under done.

Hi54putty · January 5

I agree. I cook them uncovered at 275-300 for five hours or until the pass all the usual tests.

lousubcap · January 5

Here's another option-Basically ribs are cooked as usual (bone side down for me) for the first X hours. Then they are removed from the cooker and wrapped with liquid (Q sauce, some other liquid for flavoring etc) in a foil pouch with the meat side down. This becomes step -0-. The sealed ribs are then returned to the cooker. At the end of the "0" time-frame, the ribs are removed from the foil and then put back on the BGE for the final "0" time-frame. This is when sauce is added if you desire. X-X-X defines the cook cycle. Those of us X-0-0 run without any of the above extras. The key is the bend or toothpick test-if you pick up a full rack and it bends around 90* you are finished-for less than a full rack insert a toothpick into the thickest meaty part of a rib-no resistance-finished. It's all in what you like-experiment and enjoy the journey.

ribnrun · January 5

I find that the bend test is less accurate when using the foil methods. The foil braises the ribs and makes them flexible but not necessarily tender. The bend test works for me when I have cooked them without foil. What kind of ribs are you smoking? I usually wait to see some good pullback of the meat from the bones when I use foil. Spareribs generally take longer than loin backs.

Try this approach. Cook them till you think they are done. Then sauce them and leave em on for another 30 minutes. Keep trying, and don't rely on the timing. Cook till done, not time.

Richard Fl · January 5

I have done ribs, bb, St, full brisket and beef just about every way except pre boiling over the past 10+years and have in the last year or so started doing rocket ribs.

Called them rocket ribs 'cause it only took 90 minutes at 375F indirect, notice they were full slabs ripped down the middle. Helps the cooking time and they are just as great as 225-250F for 5-6 hours IMHO. I have also done them being ripped into thirds and cooked 375F they only take 45-50 minutes.:

Here they are ready to eat:

sola · January 5

I use a method I found on here, turbo ribs. Indirect, 350 for 2 hours. Fool proof, obviously.....

ChokeOnSmoke · January 5

Way too low a cooking temp in my opinion, you were probably only hitting just over 200 at the grid level. Also, the amount of time will help you ballpark, but you need to use one of these tests to get them right:

http://amazingribs.com/tips_and_technique/are_they_ready.html

Brownie · January 5

I'm guessing you were doing baby backs by the time. Try shootin for 250* dome for that timeline, and sauce after they pass the finished test of your choice.

As you can see there are many ways, temps, and times to achieve great ribs. Give it another try with the given suggestions and you'll be cooking perfect ribs in no time.

Dave in Florida · January 5

BB's or Spares, it's turbo for me.

http://eggheadforum.com/discussion/1144307/my-turbo-ribs-tonight#latest

gdawgs24 · January 8

TRY PULLING THE SKIN MEMBRANE OFF THE BONE SIDE OF THE RIBS.

Howdy, Stranger!

Forums

Ribs help

Comments