Big Green Egg - EGGhead Forum - The Ultimate Cooking Experience...
Is your Big Green Egg still cooking even though it’s cold out? We hope so! We love the opportunity to cook heartier meals on the EGG during the winter. Some recipes you definitely want to try are Double Smoked Potatoes, BBQ Chicken Soup, Monte Cristo Sandwich and Breakfast Quiche. These are sure to keep your stomach warm & full! We can’t wait to see what winter-inspired dishes you cook!

Big Green Egg headquarters has moved - come visit our new showroom and check out the History of the EGG Museum and the Culinary Center too!  3786 DeKalb Technology Parkway, Atlanta, GA 30340.

BGE Pitting

4Runner4Runner Posts: 2,490
edited September 2012 in EggHead Forum
Burned my gasket this week so I started the replacement process this morning and after removing the old gasket and scrapping off the leftovers, I noticed pitting around the rim of the lower half of my Egg.   Is this an issue or just cosmetic?   Anyone else have this?  I have attached 3 images showing the pitting in 3 different areas along the rim.   Thanks

Ps - in the first image it does look like a wart but focus for a bit and then it will start to look like a pit and not a raised area.  Nasty looking I know!

Joe - I'm a reformed gasser-holic aka 4Runner Columbia, SC Wonderful BGE Resource Site: http://www.nakedwhiz.com/ceramicfaq.htm and http://www.nibblemethis.com/  and http://playingwithfireandsmoke.blogspot.com/2006/02/recipes.html
What am I drinking now?   Woodford....neat

Comments

  • Haven't yet replaced the gasket but I have cast ceramics.  Looks like bubbles in the slip when it was cast.  I wouldn't worry about it.
    My actuary says I'm dead.
  • I think those are just cosmetic. From what I understand it is caused by the small bits of moisture in the ceramics when being fired in a kiln. (I know the egg I am working on has them). But I could be wrong lets see what others say ... 
  • 4Runner4Runner Posts: 2,490
    Just finished the new gasket install. One thing to add, the pitting didn't show up on my last gasket install so it happened sometime in the last few years.
    Joe - I'm a reformed gasser-holic aka 4Runner Columbia, SC Wonderful BGE Resource Site: http://www.nakedwhiz.com/ceramicfaq.htm and http://www.nibblemethis.com/  and http://playingwithfireandsmoke.blogspot.com/2006/02/recipes.html
    What am I drinking now?   Woodford....neat
  • 4Runner said:
    Just finished the new gasket install. One thing to add, the pitting didn't show up on my last gasket install so it happened sometime in the last few years.
    Air bubbles, water drops, who cares?  If they were just below the surface they may have opened up over time and use.  Little thin places over the pits look fine out of the kiln.  Open and close the dome a few hundred times and perhaps they finally break and reveal pits.  Not to worry.  If it works, it works.  If the whole thing cracks, warranrty claim.  Still not to worry.
    My actuary says I'm dead.
  • 3 words: "automotive body filler".

    Of course I am only kidding....don't worry about it. Use the heck out of it...

    RicklesssS in Oregon

  • 4Runner4Runner Posts: 2,490
    Yep. No cracks so I back to cooking! Thanks.
    Joe - I'm a reformed gasser-holic aka 4Runner Columbia, SC Wonderful BGE Resource Site: http://www.nakedwhiz.com/ceramicfaq.htm and http://www.nibblemethis.com/  and http://playingwithfireandsmoke.blogspot.com/2006/02/recipes.html
    What am I drinking now?   Woodford....neat
Sign In or Register to comment.