Big Green Egg - EGGhead Forum - The Ultimate Cooking Experience...
Welcome to the EGGhead Forum - a great place to visit and packed with tips and EGGspert advice! You can also join the conversation and get more information and amazing recipes by following Big Green Egg at:

Facebook  |  Twitter  |  Instagram  |  Pinterest  |  Youtube  |  Vimeo
Share your photos by tagging us and using the hashtag #EGGhead4Life.


In Atlanta? Come visit Big Green Egg headquarters, see our new showroom and check out the History of the EGG Museum and Culinary Center!  3786 DeKalb Technology Parkway, Atlanta, GA 30340.

Dome won't stay up on cold BGE

mrjwhitmrjwhit Posts: 83
edited July 2012 in EggHead Forum
This is a normal happening.

I open my BGE with intentions of cooking like Bobby Flay. I lift the dome to inspect how much lump I have inside. Slowly and ever so gently the dome starts to close. I lift it again and again and finally it stays. Coals loaded in and lighter is in place. Lid still eases down. I get the fire going and I shut the dome. No problem. 10 minutes later when the fire is hot and I'm ready to pull out the starter, I open the dome and it stays open with no issue. 

So my question is this, is there a reason my dome won't stay open when the BGE is cold?  
Large BGE as of Father's day '12 http://www.jwhit.com

Comments

  • MO_EgginMO_Eggin Posts: 155
    Performance anxiety?
    LBGE, St. Louis, MO
  • mrjwhitmrjwhit Posts: 83
    Performance anxiety?
    I don't even know where to go with that. SMH. 
    Large BGE as of Father's day '12 http://www.jwhit.com
  • misumisu Posts: 213
    Put the metal top thing on
  • LizzieSampsLizzieSamps Posts: 894
    Performance anxiety?



    Ok just spit out my drink! FUNNY!
  • FxLynchFxLynch Posts: 433
    My only thought would be that you have it in a table and the Egg is sitting too deep, so that the posterior hinge mechanism is hitting the table top.
  • mrjwhitmrjwhit Posts: 83
    FxLynch, that's good, but it's not that at all. I made sure with the table that all hardware was away from the wood. *This baby can get hot! 
    Large BGE as of Father's day '12 http://www.jwhit.com
  • walleyvwalleyv Posts: 147
    Is the egg sitting level?
  • mrjwhitmrjwhit Posts: 83
    Good question, I ran out to confirm that it's level. It's slightly off. Not a wood-tech guy, but I'd guess maybe a smidge (scientific term). But if I'm reading it right the table is a leaning back just that tiny bid. So I'd think it would stay open and not shut. 

    About to tighten down the bolts today, since I'm not cooking today, to see if that fixes it. 
    Large BGE as of Father's day '12 http://www.jwhit.com
  • walleyvwalleyv Posts: 147

    Maybe you should loosen all the nuts and make sure you lower band is sitting as low as it can go on the egg base.  Also make sure the upper band is as far up as it can go on the dome.

     

  • walleyvwalleyv Posts: 147
    If that does not work try taking the springs off the hinges.
  • walleyvwalleyv Posts: 147
    And if that does not work call in a exorcist.
  • fishlessmanfishlessman Posts: 19,309
    first, i would check the spring bolts, if they lean in and are not perpendicular to the bracet, tighten them. second i would get a level, third i would check the springs them selves as ive replaced a cracked one. now ive only seen this a couple times over the years, the hinge was installed upsidedown, the flat section should be on top
  • nolaeggheadnolaegghead Posts: 19,654
    You may need new hinge springs.  Springs and lose tension. They should be covered under warranty.
    ______________________________________________
    This is my signature line just so you're not confused.
    Large and Medium BGE, Kamado Joe Jr., smoker with a 5k btu AC, gas grill, fire pit, pack of angry cats, two turntables and a microphone, my friend.
    New Orleans, LA - we know how to eat 

  • mrjwhitmrjwhit Posts: 83
    Tightened all the screws/bolts on the bands. Seems to have fixed the problem. I'll know for sure in the AM since I plan on cooking my first brisket on my BGE. 
    Large BGE as of Father's day '12 http://www.jwhit.com
Sign In or Register to comment.
Click here for Forum Use Guidelines.